HOW YOU CAN USE 555-TIMER TO OPERATE A BULB

HOW YOU CAN USE 555-TIMER TO OPERATE A BULB FOR A GIVEN TIME

HOW YOU CAN USE 555-TIMER TO OPERATE A BULB FOR A GIVEN TIME

How to use 555-Timer IC in a circuit to operate a Bulb (Lamp) to remain ON for minutes, before returning back to its Off state.

Stage 1

555-Timer has vast application in electronics. In my recent post I showed you other forms in which a 555-Timer could be applied. Today, we shall use 555-Timer in a Monostable Multivibrator configuration to trigger a Driver (Transistor) in energizing a relay and in turn operate a lamp of 230V AC when the relay normally open contact is energized.

Above shows a configuration of a 555-Timer connected in a monostable pattern. This is achieved by connecting Pin 6 and Pin 7 together (bridged using a jumper). Then, connect Pin 8 to the supply rail (power supply line). Then, connect a 10kΩ resistor from pin 4 to the supply rail and then, also connect a capacitor (electrolytic capacitor) of 100µF 16v from that same pin 4 to ground (0v or neutral line of the power supply). The essence of the resistor capacitor network at pin 4 is to slow down or stop immediate start up of voltage at pin 4 when the power source is turn On initially. This will eliminate false triggering of the 555-Timer from operating the Lamp when we didn’t even intend for nit to be operated. Now, from pin 7, connect a resistor of 100kΩ variable resistor in series with a 10kΩ fixed resistor to the supply rail (power supply line). That is to say that, the two resistors will be in series and one of its terminals will be connected to pin 7 and the other terminal will be connected to supply rail. The fixed resistor is to ensure that the variable resistor when adjusted to 0Ω will not affect the circuit in anyway. And now, connect a 1000µF 16v capacitor from pin 7 or pin 6 to ground (negative rail or neutral line of the power source).

Lastly in regard to the first stage, connect a resistor of 10kΩ in series with pin 2 (Trigger Pin or Input) and the supply rail. Then, connect a push button soft switch between pin 2 and ground (neutral rail). This is to keep the input to the 555-Timer IC High so as not to make it “floating” to avoid it been falsely triggered.

Stage 2

This is the last stage if I might conclude from my perspective. This is just a transistor driver stage. It is simply a transistor connected to function as a switch. When its Base-Emitter junction is forward bias by the presence of a voltage from the output of the monostable multivibrator (555-Timer), it cause the electrons to migrate from the emitter to the collector thereby causing large amount of a current to flow through the relay thereby energizing the relay and its contact is therefore closed and thus, our lamp been connected in series with the relay-contacts is operated ON. The resistor in series with the Base of the transistor is just to limit the amount of current flow into the Base of the transistor to a safe level not to damage the transistor or exceed its ratings. The relay coil terminal is connected in between the collector of the transistor and the supply rail. Note also, a diode has to be connected across the collector of the transistor and the supply rail. This is to eliminate any back-emf that might be produce by the relay coil when it de-energizes thereby damaging the transistor. Finally, the Lamp (AC Bulb) is then connector in series with the normally-Open contact of the relay and the other terminal goes to the Live connection of the AC Source. Then the other terminal goes to the Neutral Line of the AC Source.

In a nutshell, the relay is just acting in the place of a normal home switch (Lamp Switch).

Thanks for your time. Let’s make it a date tomorrow so we share another electronics idea together. You are special.

Isaac Johnson

Circuit Design And Technology

Tweet

555 TIMER AND CIRCUIT APPLICATIONS (NE555, LM555)

555 Timer Integrated Circuit are commonly use in L.E.D Sequencer, Clock Generator also known as Oscillator and in basic electronics practice. They are usually known as Timer I.C; sometimes hobbyist calls it 555 Timer.
555 Timer are widely use in the field of electronics such as in Laptops, TV, and Timer Circuits (Bomb Trigger Circuit) and so on. In Digital Clocks, Indicators requiring flashing operations, in L.E.D Sequencer use in Christmas displays and lots more down to complex applications in electronics design. Today, I shall only introduce you to basic applications of Timer Integrated Circuit and configurations (Ways of Application)
.

AS A MONOSTABLE

555 Timer can be connected to operate as a Monostable Flip-flop. As the name implies, it is a multivibrator that has only one (mono) stable state. That is to say, when it is been triggered whether intentional or unintentionally, it changes its state (output) and then later returns back to its original state where it was before it was triggered. In a way, its like saying when a monostable timer is triggered, its output changes state from Low (0) to High (1) where the Low represents the absence of a voltage or signal and the High represents the presence of a voltage or signal.

Below is a way to connect the terminals of a 555 Timer to operate or function as a Monostable flip-flop. Its pin 2 is the trigger pin, pin 3 remains the output pin, pin 6 is connected to pin 7 and a frequency determining network (RC Network) is connected between pin 7 and Vcc (Power supply line) and the Ground (0v). Remember that pin 4 and pin 8 is always connected to the supply rail (Power supply line) and pin 1 is always connected to Ground (0v).

The output of this circuit can be connected to drive a Relay, an L.E.D, and a Buzzer and so on. Note the Trigger pin (pin 2) must not or is not advisable to be left floating (unconnected) so as not to be falsely triggered by stray alternating signals around, even from your hands close to the trigger pin can cause it to be triggered. Therefore, you could connect a load resistor between pin 2 and supply rail, then having a pull0down switch from pin 2 to ground. This keeps the input of the Timer High, until when pulled down to 0v (Ground) by the switch before it triggers the circuit.

AS AN ASTABLE MULTIVIBRATOR (OSCILLATOR OR CLOCK GENERATOR)

A 555 Timer connected as an oscillator or astable multivibrator operates on a free-run ground. What I meant is, it does not require your effort to cause it to oscillate (or trigger unlike a Monostable). Once the power source is powered ON, it begins to oscillate (ON and OFF alternatively and continuously) except the power source is disconnected or switch-Off.

There are cases we need this kind of operation. In events or situation where we need a clock pulse (oscillation) to be triggering our circuit independently and continuously, we then apply a 555 Timer connected as an oscillator. Please note that the waveform (wave shape) produce by a 555 Timer is a pulsing or square like waveform. This MUST not be mistaken or assumed to be a Sine Wave!

Below is a practical oscillator circuit with actual values that you can experiment with.

In 555 Timer been use as an oscillator, pin 2 is connected with pin 6, pin 4 and pin 8 is connected to the supply rail as usual as seen in the above diagram. Pin 1 is connected to 0V (Ground), Pin 3 is our Output terminal. A capacitor (say C) is connected between Pin 6 (along side pin 2) and Ground. A resistor (say R2) is connected between pin 6 and pin 7, another resistor (say R1) is connected between pin 7 and supply rail (or pin 8 and pin 4 since they both are also connected to the supply rail). The output been pin 3 could be connected to drive any load say a Relay that could in turn operate a contact to switch ON a Motor, Fan, Conveyor, Lamp, L.E.D and so on. Below shows a practical configuration and values of component use in constructing an oscillating circuit.

Ping me a mail if you have any question or assistance regarding the discussion above. I shall be there to attend to you ASAP!

Thanks for taking time to read! You are wonderful! Let’s make it a date again tomorrow, as I hope to furnish you with another interesting package. Don’t miss it!

Isaac Johnson

Circuit Design And Technology

Tweet

HOW TO CONSTRUCT A LED SEQUENCER USING CD4017

In my recent article I discuss how to use a Decade counter popularly known as CD4017 (Divide by 10) to switch a lamp or load. In this article, we shall look into how to still use a decade counter 4017 to drive series of L.E.D to form a circle, a pattern or a line etc pending on your desire.

Recall that a decade counter (also known as divide-by-10) has 10 outputs. These outputs can sink a current required to operate a L.E.D. But since we want the operation to be sequential i.e. coming on and off one after the other in ascending or descending pattern, we therefore would need another stage that will be generating a steady pulse or oscillation for us to clock the counter.

Knowing what we want, we will go for a clock generating Integrated Circuit. So far, the basic simplest bone is NE555 popularly known as a Timer I.C or Timer. In my coming article I shall discuss 555 Integrated Circuits in details.

NE555 is an 8 terminal I.C with RC (Resistor-Capacitor Network) frequency determining arrangement. The connection of 555 will determining its application as it can also be use as a Monostable Multivibrator (One-Shot Trigger). In this discussion, we shall be using it as a clock generator r oscillator to provide is a stable pulse to serve as our trigger to the counter independent of an operator manually triggering the unit to make a sequence display.

Following my connection as shown bellow, with the right component values, you will be able to construct a Timer and a counter to drive L.E.Ds.

Now, connect a fixed value resistor say 4.7k in between pin 7 and 8 of the 555 I.C.

Next, connect a 1k resistor in series with a variable resistor of 100k in between pin 7 and pin 6.

Next, connect a 10 uF capacitor in between pin 6 and pin 1 of the 555 I.C.

Next, link pin 2 of the 555 timer to pin 6 using a jumper or conductor.

Next, connect pin 4 and pin 8 of the 555 timer to your supply rail (Power supply line).

Next, connect pin 1 of the 555 timer to ground (0 V) and pin 5 of the timer should be connected with a

100nF

capacitor to ground (0v). You can check my article on Capacitors in Blog Archives for tutorials how to identify and know capacitors.

Next, your pin 3 is now your output. You should get oscillating pulse from here if you follow my instructions above.

Now, we need to fix the counter Unit. You could also check the Archives by the left pane of this site on how to use a decade counter as a switch for familiarity sake.

Now, just follow my connections as seen below, by connecting pin 8 and pin 13 of the counter 4017 to ground (0V).

Next, connect pin 16 to supply rail (power supply line). Connect pin 14 (clock input) to the pin 3 of the 555 timer. With this, you should have all your counters output jumping up and down sequentially. So, we just need to connect our LEDs to the outputs as shown below. Also, I shall give you more tutorials on LED soon ok!

Lets make it a date tomorrow as I hope to bring another information package your way again. You are special!

Isaac Johnson

Circuit Design And Technology

Tweet